LOW-PRESSURE CONTROL

More valve options.
Same low-pressure airline.

Keep the circuit you have. Add the rotary valve benefits your application needs.

Choose your application.

Separator application

WHAT YOU KEEP

Keep your existing circuit

Controller: P/P liquid-level controller

Retain the pneumatic liquid-level controller and its low-pressure arrangement for compatible snap service. Easytork brings the rotary valve, actuator and controls together, without the separate higher-pressure actuator supply shown in the alternative arrangement.

1. Existing linear arrangement
S1: 60–120 psi air supply is regulated to 35 psi or less for the P/P liquid-level controller and linear spring-diaphragm valve package.

The regulated low-pressure circuit serves the controller and linear package.

2. Higher-pressure rotary arrangement
S2: the illustrated spring-return rack-and-pinion rotary package adds airline modifications, a 40–80 psi regulated branch, and a pilot valve; the actuator label specifies at least 40 psi.

This design adds an actuator-supply branch, regulator, pilot valve, and airline modifications.

3. Easytork: drop-in rotary alternative
S3: the illustrated Easytork fail-safe rotary package uses the existing P/P controller arrangement regulated to 35 psi or less, without the separate actuator-supply branch shown in S2.

Keep the existing low-pressure controller circuit and reconnect the output airline to the Easytork package.

WHAT YOU GAIN

Add rotary valve benefits

Why rotary for separator liquid dumps?

A suitable full-port ball valve combines high capacity, protected seating and quarter-turn operation for snap-acting liquid dumps.

High capacity, a clear flow path

An unobstructed bore lets discharged liquid pass directly through the fully open valve, with fewer internal turns than conventional globe-style passages.

Seat protection at both end positions

With suitable ball-and-seat geometry, the sealing surfaces are shielded from direct abrasive flow when fully open and fully closed. Conventional globe-style plugs and seats can remain exposed to the flow when open.

Quarter-turn movement for dump cycles

A short, 90-degree stroke suits the open, dump and close sequence. Prompt transitions limit time at a restricted opening when the liquid carries sand.

See how it operates

Same controller. Same piping.
Linear or rotary.

Compare the existing linear package with the Easytork rotary package. Both operating states are shown below.

Existing valve package

Pilot valve: signal present; existing valve open.
Pilot valve: signal lost; existing valve closed.

Easytork rotary package

Pilot valve: signal present; rotary valve open.
Pilot valve: signal lost; rotary valve closed.
See it in motion
SEE IT IN MOTION

Low-pressure snap action.

Watch two valve-package demonstrations using approximately 30 psi air supply.

Easytork Series 25 · 1000 CWP

Snap-acting demonstration using approximately 30 psi air supply.

Watch on Vimeo

Balon 2-inch · 2R-S93N-SE

Snap-acting demonstration using approximately 30 psi air supply.

Actuator sizing: the current actuator provides sufficient torque for a maximum differential pressure of 2,000 psi at 35 psi air supply. Higher differential pressure requires a larger actuator, within the valve’s pressure rating.

This is an actuator-sizing limit-not the valve’s working-pressure rating or a claim that this video demonstrates operation under 2,000 psi differential pressure.

Watch on Vimeo

Easytork: field-reversible fail-open or fail-close. Choose the action your application requires.

Download

Download the published low-pressure case study and snap-acting example (PDF)

YOUR COMPLETE PACKAGE

One source for your rotary solution.

Easytork brings the valve, actuator, controls and feedback together around your application.

A compact rotary assembly can help where skid space is tight. Match the valve type, torque and fail action to the duty and available air supply.

Discuss your package

Understand performance at available pressure

Review charged supply pressure, usable torque and the required fail action.

CONTACT EASYTORK

Discuss your
current application.

Start with your headache.

Tell us about your control valve application and what you’d like to improve: reliability, speed, size, weight or low-pressure operation.

Package selection depends on valve torque, available pressure, process conditions, and required fail action. For burner or fuel service, review the required shutoff and safety functions.

Discuss my application+1 (314) 266-6880